Quick Links...



Popcam Headshots setup



NOTE: this video shows an old version of popcam. We got rid of the stool, so ignore that in the video, and raise the stand as high as possible so a user can stand for their photo.


STEP 1 - Find the best place for popcam: near an electrical outlet, ideally in front of a shaded window. Don't worry about the background.

 

STEP 2 - Open the case (press the latch buttons to release them), and take popcam and the stand out of the case.


STEP 3 - Set up the stand: Spread the stand's legs as wide as possible, then raise the stand's post to the very top and tighten the post's knob.


STEP 4 - Put popcam on the stand, vertically, and plug it into an electrical outlet.


STEP 5 - In the popcam app, follow the prompts to scan the SHOOTcode that was emailed to you.


STEP 6 - Follow the on-screen setup prompts, then press "Start Shoot".



Tips for the best lighting

  • Put popcam in front of a shaded window to get diffused light. To avoid direct sunlight, use a north-facing window .
  • Avoid placing popcam directly under strong light sources, otherwise your subject's hair may be awkwardly lit.
  • Make sure your subject stands within arms length of popcam, so popcam's lights reach the subject well.



Popcam Photo Booth setup 


STEP 1 - Find the best place for PopCam: near an electrical outlet, in a good spot, and pointed at a great backdrop.

 

STEP 2 - Open the case (press the latch buttons to release them), and take popcam and the stand out of the case.


STEP 3 - Set up the stand: Spread the stand's legs as wide as possible, then tighten the leg's knob. Raise the stand's post to the very top, then tighten the post's knob.


STEP 4 - Put popcam on the stand, horizontally, and plug it into an electrical outlet.


STEP 5 - In the Salsa app, tap your shoot, then tap "Start Event".


NOTE: If you don't see the menu...

If you open salsa and see a big blue "photo booth" circle, then you're in someone else's shoot. To get out, double tap the top left corner to open the hidden menu. In the menu, tap "dashboard" to show all the shoots. On the list of shoots, tap into yours and tap "start event".



Popcam teardown



STEP 1 - End your shoot...

            For Headshots: tap "?" in the upper right corner; then tap "End Shoot" and scan your SHOOTcode.

            For Photo Booth: double tap the upper left corner; then tap "dashboard", and go pack to the main menu.


STEP 2 - Unplug popcam and wrap its cord tightly around the back drum; then secure the cord using its clip.


STEP 3 - Remove popcam from the stand and set it aside. 


STEP 4 - Collapse the Stand: slightly loosen the stand's knobs, then lower its post and collapse its legs.


STEP 5 - Put the stool and the stand in the case. Point the stand's knobs to the side, not up.


STEP 6 - Place popcam in the case, facing up, so it rests on the case's shelves. Adjust the cord if needed.


STEP 7 - Remove the old shipping label from the case's lid and rip it up.


STEP 8 - Remove any old shipping stickers from outside the case.


STEP 9 - Print the shipping label that was emailed to you, fold it in half, and place it in the shipping label slot with the shipping info facing away from you (so that the shipping info can be viewed from the outside the case).


STEP 10 - Double check that popcam, the Stand, the Stool, and the New Shipping Label are in the case; and that the shipping label is visible when the case is closed.


STEP 11 - Close the case and secure all its latches. Check to ensure the shipping label is visible.


STEP 12 - Follow the shipping instructions that you were emailed to you. You'll either place popcam out for pickup OR take it to your local UPS store.


Once popcam is shipped, you're all done



Popcam troubleshooting


If popcam is disconnected...

  1. On popcam's screen enter the control center by swiping down on the upper right corner. Then, long press the wifi button to open its menu. In the menu, tap the hotspot icon until it says "Discoverable".
  2. Unplug popcam from the wall for 5 seconds, then plug it back in.
  3. In the control center the hotspot should change to say "1 connection". Once it does, tap back out of control center and wait for popcam to return to normal (This may take a few seconds).




If popcam is connected to the hotspot but still isn't working, restart the camera...

  1. On the back of popcam, open the small round door to be able to see the back of the camera
  2. On the camera, above the menu button, you'll see the side of the "On/Off" wheel
  3. Rotate the wheel up to turn the camera off (You'll hear the wheel click).
  4. Rotate the wheel down to turn the camera back on (You'll hear the wheel click, and the camera's lens will make a subtle noise)



Need more help?

Email help@popcam.me